How To Put Dresser Drawers Back In

Putting dresser drawers back in can be a frustrating and daunting task. I remember the first time I had to do it, I spent hours trying to figure out how to properly align the drawer with the tracks. After a lot of trial and error, I finally found a method that works every time. In this article, I will share my experience and provide a step-by-step guide on how to put dresser drawers back in.

Step-by-Step Guide

Step 1: Remove the Drawer

The first step is to remove the drawer from the dresser. To do this, gently pull the drawer out as far as it will go. Then, lift up slightly on the front of the drawer and pull it out of the track.

Step 2: Align the Tracks

Before you can put the drawer back in, you need to make sure the tracks are properly aligned. Look inside the dresser and locate the tracks that the drawer slides on. Make sure they are straight and parallel to each other. If they are not, adjust them until they are.

Step 3: Align the Drawer

Now it’s time to align the drawer with the tracks. Hold the drawer at a slight angle and line up the wheels or rollers on the bottom of the drawer with the tracks. Once the wheels are in the tracks, lower the front of the drawer and push it back until it is fully seated in the tracks.

Step 4: Test the Drawer

Finally, give the drawer a test run to make sure it is properly aligned and glides smoothly. If it doesn’t, repeat the steps above until it does.

Top 10 Tips and Ideas

1. Always remove the drawer completely before attempting to put it back in.

2. Make sure the tracks are clean and free of debris before putting the drawer back in.

3. Use a level to ensure the tracks are straight and parallel to each other.

4. If the drawer is heavy, ask someone to help you hold it while you align it with the tracks.

5. Lubricate the tracks with a silicone spray to help the drawer glide smoothly.

6. If the drawer still doesn’t glide smoothly, check the wheels or rollers on the bottom of the drawer and replace them if necessary.

7. If the tracks are damaged, replace them before attempting to put the drawer back in.

8. Don’t force the drawer into the tracks. If it doesn’t go in smoothly, something is not aligned properly.

9. If you’re unsure about how to put the drawer back in, consult the manufacturer’s instructions or seek professional help.

10. Once the drawer is back in, organize your clothes and enjoy your newly functional dresser!

Pros and Cons

Pros:

– Putting dresser drawers back in can save you money and time by avoiding the need to buy a new dresser.

– It’s a simple DIY task that anyone can do with a little patience and effort.

– Properly aligning the drawer with the tracks can prevent damage to the dresser and the drawer itself.

Cons:

– If the tracks are damaged or the wheels/rollers on the drawer are worn out, putting the drawer back in may not be possible without replacing those parts.

– It can be frustrating and time-consuming if you don’t know what you’re doing.

My Personal Review and Suggestion

Overall, putting dresser drawers back in is a task that anyone can do with a little patience and effort. I recommend following the step-by-step guide above and using the tips and ideas to make the process as smooth as possible. If you’re unsure about how to do it, don’t hesitate to seek professional help. In my experience, properly aligning the drawer with the tracks can save you money and time by avoiding the need to buy a new dresser. So, give it a try and enjoy your newly functional dresser!

Question & Answer and FAQs

Q: What if the drawers keep falling off the tracks?

A: This could be a sign that the tracks are damaged or that the wheels/rollers on the drawer are worn out. Try replacing those parts to see if it solves the problem.

Q: Can I use a different lubricant instead of silicone spray?

A: It’s not recommended to use any other lubricant besides silicone spray, as it can cause damage to the tracks and the drawer.

Q: How do I know if the tracks are aligned properly?

A: Use a level to ensure the tracks are straight and parallel to each other. If they are not, adjust them until they are.